Watch Catalog

Casio module 5613

Quartz module. 5613 is the number engraved on the caseback of these watches, and Casio files its operation manual under it. 1 watch in the catalog runs on it.

How to operate module 5613

Short steps in our words. The buttons are lettered as in Casio's operation guide, where each task's page is given.

Set the time and date

  1. In the Timekeeping Mode, hold A for at least three seconds until the city code flashes in the lower display.
  2. Press C to step through the settings: city code, DST, 12/24-hour format, seconds, hour, minutes, year, month, day, then light duration.
  3. On the 12/24-hour format, press D to switch between 12H and 24H.
  4. On the seconds, press D to reset them to 00.
  5. On the hour, minutes, year, month or day, press D to go up and B to go down.
  6. Press A to leave the setting screen.

Good to know

Select the Home City code before you change any other setting.

Resetting the seconds between 30 and 59 adds one minute.

The day of the week follows the date by itself; the hands follow the digital time.

In 12-hour format, the PM indicator marks noon to 11:59 p.m.

From Casio's guide, page E-9

Daylight saving time

  1. In the Timekeeping Mode, hold A for at least three seconds until the city code flashes.
  2. Press C: the DST setting shows.
  3. Press D to switch between on (summer time) and OFF (standard time).
  4. Press A to leave. The DST indicator shows while summer time is on.

Good to know

In the World Time Mode, holding A for at least three seconds switches DST for the city shown; doing it for the Home City switches it for the Timekeeping Mode too.

From Casio's guide, page E-12

Home City

  1. In the Timekeeping Mode, hold A for at least three seconds until the city code flashes.
  2. Press D (east) or B (west) until your city code shows.
  3. Press A to leave.

Good to know

World Time is worked out from the Home City; if a World Time city looks wrong, check the Home City and the Timekeeping Mode time.

In the World Time Mode, holding A and B until the watch beeps swaps the Home City with the city shown.

From Casio's guide, page E-9

Set an alarm

  1. Press C until the Alarm Mode shows (the mode after World Time).
  2. Press D to step through AL1, AL2, AL3, AL4, SNZ (the snooze alarm) and SIG (the hourly signal) until the alarm you want shows.
  3. Hold A for at least three seconds until the hour flashes; this also switches the alarm on.
  4. Press C to move between the hour and the minutes, and D to go up or B to go down.
  5. Press A to leave the setting screen.
  6. To switch an alarm or the hourly signal on or off, select it with D in the Alarm Mode and press A: on or OFF shows.

Good to know

An alarm sounds for 10 seconds in any mode; press any button to stop it.

The snooze alarm sounds seven times, every five minutes, unless you turn it off.

From Casio's guide, page E-35

Realign the hands

  1. In the Timekeeping Mode, hold D for at least three seconds until Sub flashes in the upper display.
  2. Check the speed hand: it should point at 50 (12 o'clock). If not, press D to move it clockwise until it does, then press C.
  3. Check the hour and minute hands: they should point at 12 o'clock. If not, press D (clockwise) or B (counterclockwise) to move them.
  4. Press A to go back to timekeeping: the hands move to the current time and the speed hand to 0.

Good to know

Strong magnetism or a knock can throw the speed, hour and minute hands off.

From Casio's guide, page E-44

Light

  1. Press B in any mode to light the face.
  2. To change the duration: in the Timekeeping Mode, hold A until the setting flashes, then press C nine times: LT1 or LT3 shows.
  3. Press D to switch between 1.5 seconds (LT1) and three seconds (LT3), then A to leave.
  4. Auto light (the face lights when you tilt the watch towards you): in the Timekeeping Mode, hold B for at least three seconds to turn it on or off; its indicator shows while it is on.

Good to know

Auto light turns itself off about six hours after you turn it on.

The light turns off whenever an alarm sounds.

From Casio's guide, page E-39

Stopwatch

  1. Press C until the Stopwatch Mode shows (the mode after the Timekeeping Mode).
  2. With the stopwatch stopped and at zero, press A to choose LAP (lap times) or SPL (split times); pick SPL for a plain elapsed time.
  3. Press D to start, D to stop, and D again to carry on.
  4. While it runs, press A for a lap or split time; in SPL, press A again to let the display catch up.
  5. When it is stopped, press A to clear it to zero.

Good to know

Make sure the speed hand is not moving before you press a button in this mode.

It counts up to 99 hours 59 minutes 59.999 seconds, then starts again from zero, and keeps running in other modes.

With a distance set (hold A for three seconds at zero), the speed hand shows speed.

From Casio's guide, page E-20

Countdown timer

  1. Press C until the Countdown Timer Mode shows (after the Stopwatch Mode).
  2. If a countdown is running, press D to pause it, then A to reset it to the start time; if it is paused, press A.
  3. Hold A for at least three seconds until the hours of the start time flash.
  4. Press C to step through hours, minutes and auto repeat; press D to go up or B to go down, or D to switch auto repeat on or off.
  5. Press A to leave the setting screen.
  6. Press D to start, D to pause, D to carry on; when paused, press A to reset.

Good to know

The start time is 1 minute to 24 hours.

At zero an alarm sounds for 10 seconds; press any button to stop it. With auto repeat on, the countdown starts again by itself.

From Casio's guide, page E-28

Module 5613 specs

Type
quartz
Power
Approx. battery life: 2 years on CR1220 · other watches that take CR1220
Accuracy
±15 seconds per month
Functions
World time, Stopwatch, Timer, Alarm/hourly time signal, Light, Light color, Calendar, 12/24-hour format
Manual
Casio's operation guide for module 5613

Watches with the 5613